Designed for installation and rapid testing of prototypes and for practical experiments with
analog and digital circuits. The contact board, which is hardwearing, is removable.
Dimensions: 340 x 265 x 130mm. Weight: 4.8kg.
The components are inserted on the contact board with the normal pitch spacing of 2.54mm.
There are 1896 contact points divided into:
12 contact points of supply lines
256 separate sets of 5 contact points receiving components and interconnetions.
4 SUPPLIES
Positioned in view immediately on the face, they are protected against short circuits
- Variable DC from 0 to +15V 300mA (ripple 30mV)
- Variable DC from 0 to -15V 300mA (ripple 30mV)
- Fixed DC +5V, 1A (100mV ripple)
- Fixed DC -5V, 100mA (30mV ripple)
1 FUNCTION GENERATOR
From 0.1Hz to 200kHz in 6 ranges varied with a control dial. The output is protected against
short circuits. - Sinewave, level variable from 0 to 10V peak-to-peak - Triangular wave, level
variable from 0 to 5V peak-to-peak - Square wave, level variable from 0 to 15V peak-to-peak
2 DIGITAL DISPLAYS
7 segments and decimal point display. Switched by the inputs of D1 & D2.
- Direct control of each segment, a b c d e f
- Access to the input of the ABCD decoder IC
1 DC DIGITAL VOLTMETER
3 1/2 digits with a maximum reading of 2,000.
Ranges 200mV-2-20-200VDC. Input impedance 10MΩ
1 UNIVERSAL COUNTER 8 DIGITS
Frequencymeter 1 Hz to 100MHz. Periodmeter 99,999 999µs.
TTL & CMOS Internal/External Input
8 DIODE DISPLAY
Status from 0 to 7 with lamps to view logic levels.
10 LOGIC SWITCHES
- 8 with 2 positions giving a voltage a either 0 or 5V
- 2 with 3 positions giving voltages of -5V 0V +5V
2 LOGIC PUSHBUTTONS
2 anti-bounce outputs A and A (respectively B and B) supplying a level between 0 and 5V
on the side of the unit.
4 ADAPTERS
These adapters allow the unit to be connected to an external electronic unit.
- 2 banana inputs of 4mm diameter
- 2 inputs of female BNC connectors
analog and digital circuits. The contact board, which is hardwearing, is removable.
Dimensions: 340 x 265 x 130mm. Weight: 4.8kg.
The components are inserted on the contact board with the normal pitch spacing of 2.54mm.
There are 1896 contact points divided into:
12 contact points of supply lines
256 separate sets of 5 contact points receiving components and interconnetions.
4 SUPPLIES
Positioned in view immediately on the face, they are protected against short circuits
- Variable DC from 0 to +15V 300mA (ripple 30mV)
- Variable DC from 0 to -15V 300mA (ripple 30mV)
- Fixed DC +5V, 1A (100mV ripple)
- Fixed DC -5V, 100mA (30mV ripple)
1 FUNCTION GENERATOR
From 0.1Hz to 200kHz in 6 ranges varied with a control dial. The output is protected against
short circuits. - Sinewave, level variable from 0 to 10V peak-to-peak - Triangular wave, level
variable from 0 to 5V peak-to-peak - Square wave, level variable from 0 to 15V peak-to-peak
2 DIGITAL DISPLAYS
7 segments and decimal point display. Switched by the inputs of D1 & D2.
- Direct control of each segment, a b c d e f
- Access to the input of the ABCD decoder IC
1 DC DIGITAL VOLTMETER
3 1/2 digits with a maximum reading of 2,000.
Ranges 200mV-2-20-200VDC. Input impedance 10MΩ
1 UNIVERSAL COUNTER 8 DIGITS
Frequencymeter 1 Hz to 100MHz. Periodmeter 99,999 999µs.
TTL & CMOS Internal/External Input
8 DIODE DISPLAY
Status from 0 to 7 with lamps to view logic levels.
10 LOGIC SWITCHES
- 8 with 2 positions giving a voltage a either 0 or 5V
- 2 with 3 positions giving voltages of -5V 0V +5V
2 LOGIC PUSHBUTTONS
2 anti-bounce outputs A and A (respectively B and B) supplying a level between 0 and 5V
on the side of the unit.
4 ADAPTERS
These adapters allow the unit to be connected to an external electronic unit.
- 2 banana inputs of 4mm diameter
- 2 inputs of female BNC connectors
Eigenschaften
- AT102/ELE