Pneumatische opstelling op statief en rooster
zonder PLC sturing
GENERAL CHARACTERISTICS
This line with conveyor belt allows the introduction to pneumatic components to be combined with programming on any automated system (in positive or negative logic). A manual control box delivered can be connected to the input-output socket in place of the PLC. The manual control box drives the actuators and shows the state of the sensors. It thus facilitates the purely pneumatic study of the components, the problems linked with speed of displacement, cushioning the end of travel, control of rate, needle screw, accuracy of magnetic detectors etc.
A manual gives details of the operation of all the electro-pneumatic components used and their adjustment. Several cycles are described, including one complete with its grafcet.
OPERATING CYCLE
The parts placed on the conveyor belt are held by the vacuum suction grip of a firstpneumatic jack, then placed on the horizontal jack, grasped by the electromagnet jack undergoing a complete handling cycle before being returned to the belt.
PNEUMATIC COMPONENTS
• 3 double effect pneumatic jacks Ø32mm. Travel 250mm, each equipped with:
- flow reducers allowing fine adjustment of their movement
- magnetic position detectors (2 or 3 per actuator) with LED
- quick-fit joints for Ø4mm tubes
• 2 5/2 electropneumatic distributors
• 1 5/3 electropneumatic distributor
All distributors are fitted with
- 24V DC coils
- LED visual display of the state of the coils
- quick-fit joints for Ø4mm tubes
- fitted on mountings with silencers
• Vacuum generator
One of the actuators is fitted with a suction grip with its vacuum system.
An adjustable threshold vacuostat delivers an electrical presence or absence
of vacuum signal.
A vacuometer allows visual checking on the vacuum.
• Jacks protection
To avoid any risk of destroying a pneumatic jack, an entirely pneumatic logic
system (without student access) prevents the simultaneous movement of the
horizontal jack with a vertical jack.
ELECTRIC BOX
• Contains a regulated 24V DC 2A source to feed the PLC if necessary if it does
not have an internal supply. The necessary supplies to the model.
• A Start cycle button, a Stop cycle button,
• a reset button.
• a general emergency button stopping the electric and pneumatic supplies.
• The connector which the user connects to the PLC or to the manual control box.
USER’S PROTECTION
• A transparent color door is a barrier between the pneumatic jacks and the
user’s hand. The opening turns off the air pressure
TWIDO PLC (only for PNEU99 version)
• 14 inputs / 10 outputs
• 2 languages : Grafcet instructions, ladder language.
• Programming : from a PC using a TWIDO software (included).
OTHER CHARACTERISTICS
The conveyor belt is either controlled by the automatic system and the end of belt
detection switch or by being forced into operation. An electromagnet illustrates
picking up by a magnetic field. PNEU is delivered on a 1000x750mm chassis with
lateral fixing brackets on a table. The model is delivered ready for use (the electric
part is completely wired and all the pneumatic connections made). The quick-fit
joints allow dismounting/reassembly of pneumatic interconnections with Ø4mm
tubes of various colors
zonder PLC sturing
GENERAL CHARACTERISTICS
This line with conveyor belt allows the introduction to pneumatic components to be combined with programming on any automated system (in positive or negative logic). A manual control box delivered can be connected to the input-output socket in place of the PLC. The manual control box drives the actuators and shows the state of the sensors. It thus facilitates the purely pneumatic study of the components, the problems linked with speed of displacement, cushioning the end of travel, control of rate, needle screw, accuracy of magnetic detectors etc.
A manual gives details of the operation of all the electro-pneumatic components used and their adjustment. Several cycles are described, including one complete with its grafcet.
OPERATING CYCLE
The parts placed on the conveyor belt are held by the vacuum suction grip of a firstpneumatic jack, then placed on the horizontal jack, grasped by the electromagnet jack undergoing a complete handling cycle before being returned to the belt.
PNEUMATIC COMPONENTS
• 3 double effect pneumatic jacks Ø32mm. Travel 250mm, each equipped with:
- flow reducers allowing fine adjustment of their movement
- magnetic position detectors (2 or 3 per actuator) with LED
- quick-fit joints for Ø4mm tubes
• 2 5/2 electropneumatic distributors
• 1 5/3 electropneumatic distributor
All distributors are fitted with
- 24V DC coils
- LED visual display of the state of the coils
- quick-fit joints for Ø4mm tubes
- fitted on mountings with silencers
• Vacuum generator
One of the actuators is fitted with a suction grip with its vacuum system.
An adjustable threshold vacuostat delivers an electrical presence or absence
of vacuum signal.
A vacuometer allows visual checking on the vacuum.
• Jacks protection
To avoid any risk of destroying a pneumatic jack, an entirely pneumatic logic
system (without student access) prevents the simultaneous movement of the
horizontal jack with a vertical jack.
ELECTRIC BOX
• Contains a regulated 24V DC 2A source to feed the PLC if necessary if it does
not have an internal supply. The necessary supplies to the model.
• A Start cycle button, a Stop cycle button,
• a reset button.
• a general emergency button stopping the electric and pneumatic supplies.
• The connector which the user connects to the PLC or to the manual control box.
USER’S PROTECTION
• A transparent color door is a barrier between the pneumatic jacks and the
user’s hand. The opening turns off the air pressure
TWIDO PLC (only for PNEU99 version)
• 14 inputs / 10 outputs
• 2 languages : Grafcet instructions, ladder language.
• Programming : from a PC using a TWIDO software (included).
OTHER CHARACTERISTICS
The conveyor belt is either controlled by the automatic system and the end of belt
detection switch or by being forced into operation. An electromagnet illustrates
picking up by a magnetic field. PNEU is delivered on a 1000x750mm chassis with
lateral fixing brackets on a table. The model is delivered ready for use (the electric
part is completely wired and all the pneumatic connections made). The quick-fit
joints allow dismounting/reassembly of pneumatic interconnections with Ø4mm
tubes of various colors
Eigenschappen
- PNEU98/ELE